Annealing for Heat Resistance: What It Can and Can't Do

Man operating a 3D printer with spools of filament
Photo by Snapmaker 3D Printer on Unsplash

TL;DR: Annealing, a heat treatment, makes polylactic acid (PLA) parts a bit more resistant to heat warp, but it also shrinks them.6 For functional parts that face heat, impact, or moisture, use rPETG, a recycled version of a more durable, heat-tolerant filament (PETG), instead.3

Annealing gives PLA a small boost in heat resistance, not a new material. Annealing PLA for heat resistance is a trade between what it buys and what it costs.5

The cost is size. The annealing process shrinks and hardens the part, so you have to plan for it before you print.6

Annealing and Heat Resistance

Many studies have confirmed that annealing improves the properties of 3D-printed PLA.4 One 2018 report found a significant improvement in the mechanical properties of printed PLA parts after heat treatment.4

Better mechanical properties and better heat resistance are two different questions. A part that improves in one area still needs its own heat test in your own setup.

What Annealing Cannot Do

Think of annealing as a small step up, not a switch to a different material. PLA suits display models, prototypes, and parts where heat and mechanical stress are not factors.3

If a part must live near real heat, change the material instead of the process. PETG is a more durable filament that can handle higher temperatures than PLA.2

Plan the size first, because the annealing process shrinks the part.6

How to Anneal PLA Parts

  1. The choice comes down to what the part must survive, not what looks easiest to print.3 If real heat is involved, skip ahead to the rPETG section and save yourself the extra work.
  2. Print slightly oversize. Account for the shrinkage by making the unannealed part slightly larger.6 Write down the scale you used so you can adjust it on the next trial.
  3. Use dry, consistent filament. One print profile only holds with consistent, dry filament.5 Print your test part and your final part from the same spool so the comparison is fair.
  4. Heat-treat the part. Use a heat source you can measure, not a guess.
  5. Measure the result. Compare the finished part with your drawing and check any mating parts. One maker makes stepper mounts and gears larger before annealing, as needed.6
  6. Test under real conditions. Put the part under the load and warmth it will see in use. Do this before you print a full batch.

When rPETG Is the Better Choice

PETG filament is tough, durable, and flexible.2 It is also incredibly adhesive, so prints can be tricky to pry from the print bed.2

PLA still wins on precision, because it holds fairly tight tolerances and produces a clean surface finish without a heated chamber.3

Choose PLA when fit matters more than heat. Choose rPETG when the job is hot, rough, or wet.

Quick Decision Check

Ask four questions before you spend time on annealing.

  • Will the part sit near heat, such as a sunny window or a warm motor?
  • Will it take impacts or carry load?
  • Will it get wet?
  • Does it need a tight fit?

A yes to heat, impact, or moisture points to rPETG. A yes to a tight fit alone points to PLA, which holds fairly tight tolerances,3 though annealing shrinks the part.6

Common Mistakes

  • Skipping the oversize step, then wondering why the part no longer fits.
  • Changing two settings at once, so you cannot tell which one helped.
  • Mixing spools between the test part and the final part.

Practical Tips

Print one small test part before a batch. PLA is not typically recycled because suitable facilities are lacking, which is one more reason to test small.1

Keep a simple log. Note the filament, the scale, the heat-treatment settings, and the measured size change for each trial.

Next time, print one gear or stepper mount slightly larger, anneal it, and measure the change. Use that measurement to scale the rest of the batch.

Sources / References

  1. PETG vs PLA: Key Differences, Strength, and How to Choose (wevolver.com) ↩
  2. PETG Filament Guide (Best Speed and Temperature...) - 3DSourced (3dsourced.com) ↩
  3. PLA vs rPETG: Functional & Display Parts FDM Guide (fast3dprint.eu) ↩
  4. Enhancement of Mechanical Properties of FDM‐PLA Parts via Thermal... (researchgate.net) ↩
  5. PLA Temperature: Nozzle, Bed & Chamber Settings (spoolharbo.com) ↩
  6. filament choice - Can you put PLA parts in your car (in the sun)? (3dprinting.stackexchange.com) ↩